The Two-Person Podcast Stack (2026): Mics, Mixer, Headphones and Arms

Everything two hosts need to record a podcast at home: two dynamic mics, a two-mic podcast mixer, two pairs of closed-back headphones, boom arms and cables.

By
Sajime
Published
Reading time
6 min

DisclosureWe may earn a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate we earn from qualifying purchases.

Our picks at a glance

Our picks at a glance
#ProductBest forRatingLinks
01RØDECaster DuoThe mixer and recorder
02RØDE PodMicThe mics (buy two)
03Audio-Technica ATH-M20xThe headphones (buy two)
04RØDE PSA1+ Professional Studio ArmThe boom arms (buy two)
05Hosa HMIC-010 Pro Microphone Cable (10 ft)The cables (buy two)
06Zoom PodTrak P4Alternative recorder (portable)
07Focusrite Scarlett 2i2 (4th Gen)Alternative (computer-based)
08Shure SM7BThe upgrade mic
No.1The mixer and recorder
RØDE

RØDECaster Duo

Two high-gain mic inputs, two headphone outputs and recording to microSD, USB storage or a computer. Made for two people at one desk.

Mic inputs
2 Neutrik combo inputs (mic, instrument, line)
Preamps
Revolution Preamps, 76 dB gain, -131.5 dBV EIN
Phantom power
Yes (+48V on the XLR inputs)
No.2The mics (buy two)
RØDE

RØDE PodMic

An end-address dynamic podcast mic with a tight cardioid pattern and a built-in pop filter. Dynamic mics keep the other host and the room quieter in each channel.

Type
Dynamic, cardioid, end-address
Frequency range
20 Hz – 20 kHz
Sensitivity
-57 dB re 1 V/Pa
No.3The headphones (buy two)
Audio-Technica

Audio-Technica ATH-M20x

Closed-back, so neither host's headphones leak into the mics, and each person can hear themselves and their co-host.

Type
Closed-back dynamic
Driver
40 mm
Frequency response
15 Hz – 20 kHz
No.4The boom arms (buy two)
RØDE

RØDE PSA1+ Professional Studio Arm

Desk-clamp arms that hold each mic at mouth height and swing out of the way when you're done. RØDE names the PodMic among the mics it supports.

Mic weight supported
94 g – 1.2 kg
Reach
940 mm (37 in) horizontal, 860 mm (34 in) vertical
Mounting
Desk clamp (desks up to 70 mm thick) or threaded desk insert (up to 55 mm)
No.5The cables (buy two)
Hosa

Hosa HMIC-010 Pro Microphone Cable (10 ft)

One 10 ft XLR cable per mic, long enough to run along a boom arm to a mixer in the middle of the desk.

Connectors
REAN XLR3F to REAN XLR3M
Length
10 ft
Conductors
20 AWG oxygen-free copper
No.6Alternative recorder (portable)
Zoom

Zoom PodTrak P4

Four XLR inputs, four headphone outputs and AA battery power. The pick if you also record on location or plan to add guests.

Mic inputs
4 XLR
Mic gain
Up to 70 dB
Phantom power
+48V on all XLR inputs
No.7Alternative (computer-based)
Focusrite

Focusrite Scarlett 2i2 (4th Gen)

Two mic preamps with Auto Gain, if you'd rather record into a DAW. It has only one headphone output, so the second host needs a headphone amp or splitter.

Inputs
2 mic preamps (combo XLR/line/instrument)
Outputs
2 balanced line outputs, 1 headphone output
Conversion
24-bit / up to 192 kHz
No.8The upgrade mic
Shure

Shure SM7B

The classic broadcast dynamic. It needs a lot of clean gain, and RØDE rates the RØDECaster Duo's preamps at 76 dB.

Type
Dynamic, cardioid
Frequency response
50 Hz – 20 kHz
Sensitivity
-59 dBV/Pa (1.12 mV/Pa)

A two-person podcast at home needs five things, most of them times two: two dynamic mics (RØDE PodMic), one mixer or recorder with two mic inputs (RØDECaster Duo), two pairs of closed-back headphones (Audio-Technica ATH-M20x), two boom arms (RØDE PSA1+) and two XLR cables. With that, each host gets their own mic, you can hear each other, and you’re recorded on separate tracks to a memory card or straight into a computer. Below is why each piece is here, plus a portable alternative and a computer-based one.

How the stack connects

  • Mic → XLR cable → RØDECaster Duo, one per host. The PodMic is a dynamic mic, so leave phantom power off.
  • Headphones → RØDECaster Duo. RØDE lists two headphone outputs, one per host, so nobody has to share or use a splitter.
  • RØDECaster Duo → microSD card, USB drive or computer (USB-C). You can record without a computer at all, or use it as an interface for your DAW or a remote-call app.
  • Boom arms clamp to the desk, so each mic sits in front of its host and the desk stays clear.

1. The mixer and recorder: RØDECaster Duo

RØDE

RØDECaster Duo

Compact podcast production studio with two high-gain mic inputs, two headphone outputs and recording to microSD, USB storage or a computer. Built for two-person shows.

Mic inputs
2 Neutrik combo inputs (mic, instrument, line)
Preamps
Revolution Preamps, 76 dB gain, -131.5 dBV EIN
Phantom power
Yes (+48V on the XLR inputs)

A two-person show needs two mic inputs and, ideally, two headphone outputs. The RØDECaster Duo has both. RØDE lists two Neutrik combo inputs with Revolution Preamps (76 dB of gain, -131.5 dBV EIN), two headphone outputs, a 3.5 mm TRRS headset input, Bluetooth for phone calls, two USB-C interfaces and multitrack or stereo recording to microSD, USB storage or a computer.

Why a podcast mixer instead of a plain interface? You can record without opening a laptop. Each host gets their own headphone volume. And you can bring a caller in over Bluetooth or USB without extra software routing.

Watch out: if you’ll often have a third person in the room, two mic inputs will be the limit. Look at the Zoom PodTrak P4 below, or RØDE’s bigger RØDECaster Pro II.

2. The mics: RØDE PodMic (x2)

RØDE

RØDE PodMic

End-address dynamic podcast mic with a tight cardioid pattern, internal pop filter and an integrated swing mount. XLR only, no phantom power needed.

Type
Dynamic, cardioid, end-address
Frequency range
20 Hz – 20 kHz
Sensitivity
-57 dB re 1 V/Pa

Dynamic mics are the standard choice for podcasting in untreated rooms. They’re less sensitive than condensers, so each host’s mic picks up less of the other host and less room echo. That matters more with two people than with one. Our guide to dynamic vs condenser mics for a bedroom studio explains why.

RØDE describes the PodMic as an end-address dynamic mic with a tight cardioid pattern, an internal pop filter and a built-in swing mount. Its datasheet lists a 20 Hz – 20 kHz frequency range and says it needs no phantom power. End-address means you talk into the top of the mic, not the side.

Budget swap: the Shure SM58 is a rugged dynamic mic that also needs no phantom power. It’s a handheld vocal mic, so it sits in a mic clip on the boom arm instead of a built-in mount. Shure lists an A25D swivel stand adapter (its mic clip) in the box, so you don’t need to buy one.

USB later? If you also want to record on your own without the mixer, a hybrid USB/XLR mic like the Shure MV7+ works both ways. See USB mic vs XLR mic + interface.

3. The headphones: Audio-Technica ATH-M20x (x2)

Audio-Technica

Audio-Technica ATH-M20x

Entry-level closed-back studio headphones. Closed back keeps the click track out of your vocal mic.

Type
Closed-back dynamic
Driver
40 mm
Frequency response
15 Hz – 20 kHz

Each host should wear closed-back headphones. Open-backs leak into the mics, and with two people talking, that leak shows up as echo on both tracks. The ATH-M20x is Audio-Technica’s entry closed-back studio model, with 40 mm drivers. Headphones also help each host hear their own mic technique: too close, too far or off to the side. Our open-back vs closed-back guide has more on why.

For more options, see our studio headphones section.

4. The boom arms: RØDE PSA1+ (x2)

RØDE

RØDE PSA1+ Professional Studio Arm

Desk-mounted boom arm for mics from 94 g to 1.2 kg, with a desk clamp, a threaded desk insert and cable management for XLR or USB.

Mic weight supported
94 g – 1.2 kg
Reach
940 mm (37 in) horizontal, 860 mm (34 in) vertical
Mounting
Desk clamp (desks up to 70 mm thick) or threaded desk insert (up to 55 mm)

Boom arms keep each mic at mouth height and at a steady distance from each host, and let you swing the mics away between episodes. RØDE lists a supported mic weight of 94 g to 1.2 kg, a horizontal reach of 940 mm (37 in), and a desk clamp for desks up to 70 mm thick. RØDE names the PodMic among the mics the PSA1+ is built for.

Before you buy, measure your desk. Check that it’s no thicker than 70 mm at the edge and that there’s room for two clamps far enough apart that the arms won’t bump into each other.

Alternative: if your desk can’t take a clamp, a floor boom stand like the On-Stage MS7701B from our starter stack works too.

5. The cables: Hosa HMIC-010 (x2)

Hosa

Hosa HMIC-010 Pro Microphone Cable (10 ft)

10 ft XLR female to XLR male mic cable with REAN (by Neutrik) connectors. Connects the mic to the interface.

Connectors
REAN XLR3F to REAN XLR3M
Length
10 ft
Conductors
20 AWG oxygen-free copper

One XLR (female) to XLR (male) cable per mic. Ten feet is enough to run each cable along a boom arm and back to the mixer in the middle of the desk.

Alternative recorder: Zoom PodTrak P4

Zoom

Zoom PodTrak P4

Small four-mic podcast recorder that runs on AA batteries, records each mic to its own track on an SD card and gives every guest a headphone output.

Mic inputs
4 XLR
Mic gain
Up to 70 dB
Phantom power
+48V on all XLR inputs

The PodTrak P4 is the pick if you’ll record away from your desk or want room for guests. Zoom lists four XLR inputs with up to 70 dB of gain, phantom power on all of them, and four headphone outputs, each with its own volume. It records each input to its own track on an SD card, runs on two AA batteries or USB power, and doubles as a 2-in/2-out USB interface.

Trade-off: Zoom lists recording at 16-bit/44.1 kHz. That’s fine for spoken word, but it’s a lower spec than most current interfaces.

Alternative (computer-based): Focusrite Scarlett 2i2 (4th Gen)

Focusrite

Focusrite Scarlett 2i2 (4th Gen)

Two-mic-input USB-C interface with Auto Gain and Clip Safe, so beginners can set levels without guessing.

Inputs
2 mic preamps (combo XLR/line/instrument)
Outputs
2 balanced line outputs, 1 headphone output
Conversion
24-bit / up to 192 kHz

If you already edit in a DAW and always record at the computer, a two-input interface is the leanest way to get two mics on separate tracks. Focusrite lists 69 dB of preamp gain and Auto Gain to set levels. The catch for two people is that it has one headphone output, so the second host needs a small headphone amp or splitter. Compare options in our best audio interfaces for home recording.

The upgrade mic: Shure SM7B

Shure

Shure SM7B

The classic broadcast and vocal dynamic mic. Forgiving in untreated rooms, but low output, so it needs plenty of clean gain.

Type
Dynamic, cardioid
Frequency response
50 Hz – 20 kHz
Sensitivity
-59 dBV/Pa (1.12 mV/Pa)

When you’re ready to upgrade the mics, the SM7B is the broadcast classic. It’s a low-output dynamic mic (Shure lists -59 dBV/Pa), so it needs plenty of clean gain. On paper, the RØDECaster Duo’s 76 dB preamps cover that without an inline booster. With a lower-gain interface, plan on one.

Nice-to-have extras

  • Foam windscreens for each mic, if a host talks very close or has strong “p” pops.
  • A microSD card for the RØDECaster Duo (or an SD card for the PodTrak P4) if you want to record without a computer.
  • Acoustic treatment: a few absorption panels, or a rug and curtains, cut down echo for both hosts. See acoustic treatment.

Bottom line

Two dynamic mics, a two-input podcast mixer, two pairs of closed-back headphones, two arms and two cables. That’s the whole two-person podcast studio. Pick the RØDECaster Duo for a fixed desk setup, the Zoom PodTrak P4 if you’ll travel or add guests, and a Scarlett 2i2 if you’d rather keep everything in your DAW and can add a headphone amp.

Solo for now? Start with our starter home studio stack and add a second mic later.

How we tested

We haven't recorded a two-person show with this stack yet. We built it from the makers' own specs (RØDE, Zoom, Focusrite, Shure, Audio-Technica and Hosa product pages, datasheets and manuals), checked that every part connects to the next and that the mixer has enough inputs, gain and headphone outputs for two people, and read long-term owner reports. Once we've recorded a two-voice test conversation through this stack, we'll add the clips and our notes here.

Frequently asked questions

Q1What equipment do you need for a two-person podcast?

Two microphones, a mixer, recorder or interface with at least two mic inputs, two pairs of closed-back headphones (and a way to plug both in), two mic stands or boom arms, two XLR cables, and a computer or memory card to record to.

Q2Can two people podcast with one microphone?

You can, but it's a compromise. One shared mic records each voice at a different distance and level, and you can't fix one host without changing the other. Two mics on separate tracks are much easier to edit.

Q3Do I need a podcast mixer or is an audio interface enough?

An interface with two mic inputs, like the Focusrite Scarlett 2i2, is enough if you record into a computer. A podcast mixer like the RØDECaster Duo adds a second headphone output, recording to a memory card without a computer, Bluetooth phone calls and sound pads. That matters more once you record regularly or take calls.

Q4Why dynamic mics for podcasting?

Dynamic mics are less sensitive than condensers. In a shared, untreated room, each mic picks up less of the other host and less room echo. Our guide to dynamic vs condenser mics has the details.

Q5Can I use two USB mics for a two-person podcast?

It's possible but fiddly. Most recording software records from one audio device at a time, so two USB mics need workarounds like a macOS aggregate device, and the two mics' clocks can drift apart. A mixer or interface with two XLR inputs avoids all that. Some hybrid mics, like the Shure MV7+, also have an XLR output for exactly this reason.

Q6Does the RØDECaster Duo record each host on a separate track?

RØDE lists multitrack or stereo recording to microSD, USB storage or a computer. With separate tracks, you can fix one host's level or noise without touching the other.