Open-Back vs Closed-Back Studio Headphones: Which Do You Need?

Open-back or closed-back studio headphones? How each design works, why closed-back is for recording and open-back for mixing, and which to buy if you can only have one.

By
Sajime
Published
Reading time
4 min

DisclosureWe may earn a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate we earn from qualifying purchases.

Record with closed-back headphones, mix with open-back. Closed-back cups seal around your ears, so the backing track stays out of your mic and the outside world stays out of your ears. Open-back cups let air and sound pass through. That avoids the pressure build-up you get in a sealed cup, and it’s why most mixing headphones are open. Can only buy one pair, and you record with a mic? Go closed-back. If you only mix, or plug your instruments straight into your interface, open-back is the better tool.

We haven’t put these headphones through our own tracking and mixing sessions yet. When we do, we’ll add what we heard here, including any click bleed that sneaks into a vocal take.

How closed-back headphones work

Each earcup is a sealed shell. Sound from the driver goes into your ear, and very little gets out.

Here’s what that means for you:

  • Isolation in both directions. Your mic doesn’t hear the click or the backing track, and you hear less of the room, your laptop fan and the street.
  • Built for tracking. This is why almost every recording session uses closed-back headphones, for singers, podcasters, and anyone sitting near a live mic.
  • The trade-off. A sealed cup traps a small pocket of air around your ear. People often describe closed-backs as sounding more “in your head” than open-backs, and they can get warm over a long session.

How open-back headphones work

The outside of each earcup is a grille or mesh, so the back of the driver is open to the air.

In practice:

  • No sealed cavity. With no closed shell behind the driver, open-back designs avoid the reflections and pressure build-up inside the cup. That’s the main reason people prefer them for mixing and critical listening.
  • They leak. Anyone next to you hears what you’re playing, and a nearby mic will pick it up too. Don’t wear open-backs while you record vocals or acoustic instruments.
  • No isolation. You’ll hear your room, so they suit a quiet space. In a noisy apartment or on the train, they’re the wrong pick.

Side-by-side comparison

Closed-back Open-back
Best for Recording, podcasting, noisy rooms Mixing, critical listening in a quiet room
Leaks into a mic Very little Yes
Blocks outside noise Yes No
Long-session heat Can get warm Usually cooler
Use on the go Yes Not really
If you only buy one Choose this if you record with a mic Choose this if you only mix or record direct

Which should you buy?

You record vocals, podcasts or acoustic instruments

Get closed-back. Leak from open-backs ends up in your recording, and there’s no getting it out afterwards. Here are closed-back studio models from budget to mid-range:

Audio-Technica

Audio-Technica ATH-M20x

Entry-level closed-back studio headphones. Closed back keeps the click track out of your vocal mic.

Type
Closed-back dynamic
Driver
40 mm
Frequency response
15 Hz – 20 kHz

The ATH-M20x is the closed-back pair in our starter home studio stack. According to Audio-Technica, it’s an entry model with 40 mm drivers and a fixed single-sided cable.

beyerdynamic

beyerdynamic DT 770 PRO (80 ohms)

Closed-back studio headphones with replaceable ear pads. A common pick when one pair has to handle both recording and mixing.

Type
Closed-back, over-ear, dynamic
Impedance
80 ohms
Frequency response
5 Hz – 35 kHz

The DT 770 PRO (80 ohms) is a common pick when one pair has to cover both recording and mixing. beyerdynamic lists replaceable ear pads and a 3 m cable.

You mostly mix, or record direct

Get open-back. If your guitar, keys or synths go straight into your interface, there’s no mic for anything to leak into, so you get all the upsides of an open design while you mix.

Sennheiser

Sennheiser HD 600

Long-running open-back reference headphones used for mixing. At 300 ohms they need a strong headphone output.

Type
Open-back, over-ear, dynamic
Impedance
300 ohms
Frequency response
12 Hz – 40.5 kHz

The HD 600 has been an open-back mixing reference for a long time. Watch its 300-ohm impedance, though, and check that your interface’s headphone output can drive it.

beyerdynamic

beyerdynamic DT 900 PRO X

Open-back studio headphones with a 48-ohm impedance, so most audio interfaces can drive them, and a detachable mini-XLR cable.

Type
Open-back, over-ear, dynamic
Driver
STELLAR.45 dynamic driver
Impedance
48 ohms

At 48 ohms, the DT 900 PRO X is much easier to drive from a typical interface or laptop, and its mini-XLR cable is detachable.

You do both

Most home studios end up with one pair of each: closed-back for tracking, open-back for mixing. If you can only buy one pair right now, start with closed-back. It can handle both jobs, but open-backs can’t be used for recording with a mic.

Other things that matter more than you’d think

  • Impedance. High-impedance headphones (250 ohms and up) need more voltage than a lot of small interfaces can provide. Check your interface’s headphone output, or pick a lower-impedance model. Our best audio interfaces for home recording can help.
  • Detachable cable. The cable is usually the first thing to go. If you can replace it, you don’t have to replace the whole pair.
  • Replaceable ear pads. Pads wear out, especially if you wear the headphones every day. Swapping them keeps a pair going longer.
  • Semi-open designs. Some headphones sit in between. They leak less than fully open models, but they still aren’t safe next to a sensitive mic.

Where to go from here

If you’re buying your first pair, pick a closed-back from the models above and add an open-back once mixing becomes a regular thing. For more options, see our full picks in the best headphones for mixing. Adding speakers too? Check out the best studio monitors for small rooms.